实现动态显示效果的方法和以上几种基本类似，这里以滚动显示为例作一说明。对于需要滚动的文字，可以将其设置为位图格式，暂存于内存中，然后利用VC 提供的位图拷贝函数BitBlt将位图复制到显示位置。对于特殊字符或图形，则可以直接利用BitBlt函数调用到显示位置。然后在类CLEDDlg的 OnTimer函数中调用该函数，以实现文字的滚动显示。另外，也可以通过设定不同的响应时间间隔来改变文字的滚动速度。 程序清单： ORG 00H LOOP: MOV A,#0FFH ；开机初始化，清除画面 MOV P0,A ；清除P0口 ANL P2,#00 ；清除P2口 MOV R2,#200 D100MS: MOV R3,#250 ；延时100毫秒 DJNZ R3,$ DJNZ R2,D100MS MOV 20H,#00H ；取码指针的初值 l100: MOV R1,#100 ；每个字的停留时间 L16: MOV R6,#16 ；每个字16个码
上传时间： 2013-11-06
上传用户：zl520l
薄膜晶体管液晶显示器（TFT-LCD）具有重量轻、平板化、低功耗、无辐射、显示品质优良等特点，其应用领域正在逐步扩大，已经从音像制品、笔记本电脑等显示器发展到台式计算机、工程工作站（EWS）用监视器。对液晶显示器的要求也正在向高分辨率、高彩色化发展。 由于CRT显示器和液晶屏具有不同的显示特性，两者的显示信号参数也不同，因此在计算机（或MCU）和液晶屏之间设计液晶显示器的驱动电路是必需的，其主要功能是通过调制输出到LCD电极上的电位信号、峰值、频率等参数来建立交流驱动电场。 本文实现了将VGA接口信号转换到模拟液晶屏上显示的驱动电路，采用ADI公司的高性能DSP芯片ADSP-21160来实现驱动电路的主要功能。
上传时间： 2013-10-30
上传用户：hongmo
设计一种应用于某全地形ATV车载武器装置中的中控系统，该系统设计是以TMS320F2812型DSP为核心，采用模块化设计思想，对其硬件部分进行系统设计，能够完成对武器装置高低、回转方向的运动控制，实现静止或行进状态中对目标物的测距，自动瞄准以及按既定发射模式发射弹丸和各项安全性能检测等功能。通过编制相应的软件，对其进行系统调试，验证了该设计运行稳定。 Abstract: A central control system applied to an ATV vehicle weapons is designed. The system design is based on TMS320F2812 DSP as the core， uses modular design for its hardware parts. The central control system can complete the motion control of the level of weapons and equipment， rotation direction， to achieve a state of static or moving objects on the target ranging， auto-targeting and according to the established target and the projectile and the launch of the security performance testing and other functions. Through the development of appropriate software and to carry out system testing to verify the stability of this design and operation.
上传时间： 2013-11-02
上传用户：jshailingzzh
CCStudio Platinum Edition is available in a number of ways. Existingcustomers who are up-to-date with their subscription service withTexas Instruments will receive their update automatically on a CD inthe mail. New customers who wish to purchase a copy of CCStudioPlatinum Edition can order TMDSCCSALL-1 starting May 23, 2005. A120-day Trial version will be also be available on CDROM startingJuly 11, 2005. Users may order the CDROM of the 120-day free copy
上传时间： 2014-12-28
上传用户：gououo
This application note contains a reference design consisting of HDL IP and Xilinx AdvancedConfiguration Environment (ACE) software utilities that give designers great flexibility increating in-system programming (ISP) solutions. In-system programming support allowsdesigners to revise existing designs, package the new bitstream programming files with theprovided software utilities, and update the remote system through the JTAG interface using theEmbedded JTAG ACE Player.
上传时间： 2013-11-14
上传用户：JIMMYCB001
The XPS Ethernetlite peripheral does not provide any mechanism to access the Ethernet PHYregisters. These registers are used to configure auto negotiation parameters and to obtain PHYstatus. This application note provides reference systems and associated software to accessPHY registers by connecting the serial management bus signals MDC and MDIO to GPIOswhich the software controls directly.
上传时间： 2013-10-17
上传用户：JamesB
工作原理 该装置电路原理见图1。由红外线传感器、信号放大电路、电压比较器、延时电路和音响报警电路等组成。红外线探测传感器IC1探测到前方人体辐射出的红外线信号时，由IC1的②脚输出微弱的电信号，经三极管VT1等组成第一级放大电路放大，再通过C2输入到运算放大器IC2中进行高增益、低噪声放大，此时由 IC2①脚输出的信号已足够强。IC3作电压比较器，它的第⑤脚由R10、VD1提供基准电压，当IC2①脚输出的信号电压到达IC3的⑥脚时，两个输入端的电压进行比较， 此时IC3的⑦脚由原来的高电平变为低电平。IC4为报警延时电路，R14和C6组成延时电路，其时间约为1分钟。当IC3的⑦脚变为低电平时，C6通过VD2放电，此时IC4的②脚变为低电平它与IC4的③脚基准电压进行比较，当它低于其基准电压时，IC4的①脚变为高电平，VT2 导通，讯响器BL通电发出报警声。人体的红外线信号消失后，IC3的⑦脚又恢复高电平输出，此时VD2截止。由于C6两端的电压不能突变， 故通过R14向 C6缓慢充电，当C6两端的电压高于其基准电压时，IC4的①脚才变为低电平，时间约为1分钟，即持续1分钟报警。
上传时间： 2013-12-19
上传用户：Breathe0125
Abstract: Counterfeiting as an international industry covers virtually everything made or manufactured,from auto parts to purses and watches to prescription drugs. In contrast to other counterfeit items, the
上传时间： 2013-12-13
上传用户：阿谭电器工作室
The PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.
上传时间： 2013-11-01
上传用户：KSLYZ
This example shows how to update at regulate period the WWDG counter using theEarly Wakeup interrupt (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an interrupton falling edge.In the NVIC, EXTI line9 to 5 interrupt vector is enabled with priority equal to 0and the WWDG interrupt vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent interruptis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上传时间： 2013-11-11
上传用户：gundamwzc
