·详细说明：使用TI的TMS320VC5402 DSP实现。DTMF的拨号采用实验仪的键盘输入，解码后在液晶屏上显示- Uses TI TMS320VC5402 DSP to realize. The DTMF digit dialing uses tests the meter the keyboard entry, AFTER the decoding demonstrated on the l
上传时间： 2013-07-25
上传用户：哇哇哇哇哇
Submission must be made within 10 days AFTER the printhead upgrade.Failure to do so will void the 12-month warranty by TallyGenicom.
上传时间： 2013-11-22
上传用户：DXM35
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. AFTER debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
Abstract: Some types of loads require more current during startup than when running. Other loads can be limited to a lower-powercurrent during startup but require a higher operating current. This article describes an application circuit that automatically adjusts apower circuit’s overcurrent protection level up or down AFTER startup is complete.
上传时间： 2013-10-23
上传用户：swaylong
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行，信息不能共享，功能、效率受限，建设和维护成本高的现状，提出了采用B/S+C/S构架模式，将各现场作业管理模块和生产MIS（管理系统）集成为一体的现场作业管理系统的设计方案，做到各子系统和生产MIS软硬资源共享，做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统，各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用，目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. AFTER the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间： 2013-11-15
上传用户：han_zh
以C8051F020为核心处理器，设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络，结合嵌入式系统的软硬件技术，完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后，分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据，通过Zigbee无线网络传送到上位机，系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.AFTER accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签： C8051F020 Zigbee 汽车测试 系统设计
上传时间： 2013-11-23
上传用户：dsgkjgkjg
针对目前采用的热敏电阻测量方法，提出了采用单总线数字式温度传感器DS18B20和单片机组成的新型温度测量仪。介绍DS18B20的结构和工作原理，以及单总线工作原理，给出了由Mega8单片机和DS18B20构成的单总线温度测量仪的硬件电路及软件流程图。经试验基于单总线器件DS18B20的温度测量仪，具有测量准确、测温范围宽、体积小、控制方便等优点。 Abstract: This paper brings forward a new temperature meter composed of 1-Wire temperature sensor DS18B20 and MCU which has advantage of the thermistor. In the article, the DS18B20＇s structure and controlling principles are introduced and hardware circuit and software diagram of the temperature meter are given.AFTER been tested,the temperature meter has the advantages of accurate measurement, wide temperature range, small volume and convenient controlling.
上传时间： 2013-10-31
上传用户：hzy5825468
针对当前安检力学试验机所能完成的试验种类单一、自动化程度低等问题，提出一种以ATmega128单片机为核心控制器的安检力学试验机的设计。详细阐述了该安检力学试验机各个组成部分的设计原理和方案，并且给出了各部分的软件设计思想和操作流程。经过大量测试试验表明：设计的安检力学试验机可以完成多达十余种的力学安检试验，完全符合相关国家标准，并且具有数据采集精度高、传输速度快、操作安全简便等特点，实现了安检设备的多功能化、数字化和自动化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its core controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the operation processes of each part are given. AFTER having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The operation of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上传时间： 2013-11-05
上传用户：a67818601
Bootloader是微处理器上电时运行的第一段代码，它可以通过通信接口实现对微处理器内部应用程序的更新升级，为网络化嵌入式产品的应用程序升级带来极大的便利。由于目前没有统一嵌入式系统的Bootloader。基于NEC 78K0系列单片机自编程原理，设计出一个适用于78K0/Fx2系列单片机的Bootloader，并能够通过单片机串口在线升级应用程序。 Abstract: Bootloader is the first piece of code executed AFTER microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ series， a useful Bootloader which is suitable for 78K0/Fx2s’ series MCU is designed，the design can update the application through serial ports.
标签： Bootloader MCU 自编程
上传时间： 2013-10-26
上传用户：fang2010
CCAVR软件有ISP功能，能过调用STK500完成的，只要设置好参数，在ICCAVR中就可以给芯片编程了，还可以让程序一编译完就自动下载到芯片中，相当方便。在Tools->environment options->ISP里设定STK500.exe的路径。— 用于调用STK500程序。在Tools->In system programming 里Programmer Interface中选中STK500。— 选择STK500下载方式。在Tools->In system programming 里把Auto Program AFTER Compile 的小勾选上。— 编译后自动编程。在Tools->In system programming 中还有一些设置项，大家可以根据需要进行相关设置。下面的图片是操作过程。
上传时间： 2013-11-17
上传用户：joseph
