The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-29
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
The TJA1042 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing the differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1042 TJA
上传时间： 2014-12-28
上传用户：气温达上千万的
The TJA1051 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1051 TJA
上传时间： 2013-10-17
上传用户：jisujeke
The TRS232E is a dual driver/receiver that includes a capacitive voltage generator to supply TIA/RS-232-Fvoltage levels from a single 5-V supply. Each receiver converts TIA/RS-232-F inputs to 5-V TTL/CMOS levels.This receiver has a typical threshold of 1.3 V, a typical hysteresis of 0.5 V, and can accept ±30-V inputs. Eachdriver converts TTL/CMOS input levels into TIA/RS-232-F levels. The driver, receiver, and voltage-generatorfunctions are available as cells in the Texas Instruments LinASIC™ library.
上传时间： 2013-10-07
上传用户：waitingfy
Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
标签： Oversampling Techniques ADC fo
上传时间： 2013-12-17
上传用户：zhyiroy
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
Luminary Micro Stellaris™ microcontrollers that are equipped with an analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library or through direct writes to the device's control registers, this application note describesboth methods. The information presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
标签： Microcontr Stellaris Using the
上传时间： 2013-10-14
上传用户：blans
The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
标签： Stellaris Clocking Options for
上传时间： 2013-10-14
上传用户：pol123
