针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
第一章：MCS-51系列单片机的存储结构(4学时) ① 掌握内部数据寄存器RAM的结构、用途和特点; ② 程序存储器ROM的结构特点，编程中应注意的问题; ③ 片内、外程序存储器的确定方法。 .. 第二章：MCS-51单片机指令系统及时序(4学时) ① 111条指令的功能分类; ② 指令的寻址方式; ③ 伪指令及汇编语言源程序的格式; ④ 与指令的相关时序。 第三章：MCS-51单片机内部模块的功能介绍(8学时) ① 内部并行I/O端口的结构特点、使用中的注意事项; ② 定时/计数器的2种工作方式、4种计数模式; ③ 串行接口的4种工作模式的设定及波特率的计算; ④ 中断系统的结构、中断响应的过程和编程方法。 .. 第四章：MCS-51单片机系统的扩展及应用(8学时); ① 系统扩展的几种方法; ② 外部程序、数据存储器的扩展; ③ A/D、D/A转换器与单片机的接口电路及编程方法; ④ 键盘扫描/动态显示接口电路; ⑤ 单片机的监控电路等。
上传时间： 2013-10-17
上传用户：熊少锋
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
为解决当前计算机串行通讯接口只有USB，难以满足旧型号设备或某些单片机要求RS232通讯的问题，设计出两款RS232/USB电路。采用CH341A与MAX223集成电路芯片构建标准9线RS232/USB通用接口转换器，无需编程。采用CH341A与PIC16F877A构建单片机与计算机之间的USB通讯电路，软件遵循RS232通讯协议，硬件进行电平转换。实际使用表明，这两款产品与计算机端Windows 操作系统下的串口应用程序完全兼容，且通讯过程中无握手失败现象。 Abstract: To solve the problem that current computer serial communication only with USB interface can not satisfy with the old type equipments or MCU to communicate with RS232， two kinds of RS232/USB circuit were designed.CH341A and MAX223 integrated circuit chips were used to create a standard 9-line RS232/USB universal interface convertor without programme. CH341A and PIC16F877A chips were adopted to build the USB communication circuit between computers and MCU. The software follows RS232 communication protocol， and the hardware converts electrical levels. Actual practices indicate that the two manufactures are compatible with serial application program of Windows operation system completely，and get avoid of handshake lost.
上传时间： 2013-11-03
上传用户：siying
摘 要: 阀门开度仪以AT89C51单片机为核心, 通过在阀门电机轴上安装的电位计传感器获得阀 门电机轴的转动角位移, 从而得出阀门的开度, 达到自动检测的目的。详细介绍了串行控制的10 位A /D转换器TLC1549的特点和功能, 说明了TLC1549与AT89C51单片机在阀门开度仪中的硬件 电路和软件程序。实践证明, 该阀门开度仪数据采集准确可靠、工作稳定。 关键词: TLC1549; AT89C51单片机; 阀门开度
上传时间： 2013-10-14
上传用户：行者Xin
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：Maple
摘要：为了解决信号采集系统的同步串行通讯问题，在理解AVR 单片机SPI接口的通讯原 理和方法的基础上，分析了AVR 单片机SPI接口的工作过程，设计了AVR单片机和串行A/ D转换器的同步串行通讯接口，并用程序描述了SPI接口通讯的过程，实现了AVR单片机 通过SPI接口与串行A/D转换器之间的数据通讯。最后，用实验和数据分析验证了设计方 案的可行性。 关键词：SPI接口；AVR单片机；串行A/D
上传时间： 2013-10-31
上传用户：lilei900512
提出了一种以S3C2440A为核心处理器的银行评价器的设计方案，并结合XILINX公司的XL95144XL型CPLD，辅助S3C2440A，实现该银行评价器的各部分功能以及系统信号之间的相互协调。该评价器在系统设计上采用液晶屏显示，代替了以往简单的数码管电路的显示模式，在视觉上给人以全新的享受。同时，评价器增加了新的网络供电方式，只要将评价器连接上网络就可以正常工作，方便了客户的使用。总之，此款银行评价器采用了嵌入式系统的设计方案，大大丰富了系统功能，实现一个银行评价器设计的新突破。 Abstract: S3C2440A of SamSung company is the core component of the embedded system. A design of bank assessor based on S3C2440A was provided in this paper. It used XL95144XL combined with S3C2440A to realize all the functions and coordination with system signals. This bank assessor used LCD to display instead of the former simple digital display and provided a new seusuous enjoment. Meanwhile，it provided a new method of network power supply，that the bank assessor could regularly work once it connected to the network，which is convenient for customers to use. In a word，this assessor takes embedded system，enriches the system’s functions and reclizes a new breakout.
标签： S3C2440A
上传时间： 2013-11-03
上传用户：taa123456
生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法，仍以传统的皮尺丈量为主，测量效率不高，有时还很不方便，没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据，利用遥控小车做为载体，采用角度传感器测量角度、霍尔传感器测量水平距离等，通过单片机LM3S615进行数据计算，实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量，高度测量精度可达99.06%，水平测量精度则可达98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上传时间： 2013-10-30
上传用户：jackandlee
设计一种基于ATmega16L单片机的温度控制系统，阐述该系统的软硬件设计方案。采用模块化设计方法，利用增量式PID算法使被控对象的温度值趋于给定值。实验结果表明该系统具有良好的检测和控制功能。 Abstract: This paper designs a temperature control system based on ATmega16L，describes the hardware and software de－sign scheme of the system，adopts the modularized design method and utilizes the incremental PID algorithm to realize the temperature of controlled device incline to the given value.The experiment result indicates that the system has good detec－tion and control function
上传时间： 2013-10-09
上传用户：stvnash
