没事发个图。
标签： 运算放大器
上传时间： 2013-11-20
上传用户：banyou
直流电机驱动电路设计
上传时间： 2013-11-20
上传用户：ca05991270
低通滤波器设计
上传时间： 2013-11-20
上传用户：lyson
这里面介绍了多种数字集成电路的用法，和设计电子钟的具体电路图
上传时间： 2013-11-20
上传用户：xiehao13
Abstract: This tutorial discusses methods for digitally adjusting the output voltage of a DC-DC converter. The digital adjustmentmethods are with a digital-to-analog converter (DAC), a trim pot (digital potentiometer), and PWM output of a microprocessor.Each method is assessed and several DACs and digital potentiometers presented.
上传时间： 2013-11-20
上传用户：zycidjl
仿真使用EWB人为设置故障,模拟电路可能发生断路、短路等现象时的状态,完整表达定理的适用范围,通过传统验证和仿真软件的对比,让两者匹配到最佳状况。实验显示,使用EWB对电路可实现全面仿真,为真实实验的设计和调试奠定了基础。
上传时间： 2013-11-20
上传用户：liujinzhao
图解电子技术入门
上传时间： 2013-10-08
上传用户：lou45566
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
LNA的功能和指标二端口网络的噪声系数Bipolar LNAMOS LNA非准静态(NQS)模型和栅极感应噪声CMOS最小噪声系数和最佳噪声匹配参考文献LNA 的功能和指标• 第一级有源电路，其噪声、非线性、匹配等性能对整个接收机至关重要• 主要指标– 噪声系数(NF)取决于系统要求，可从1 dB 以下到好几个dB， NF与工作点有关– 增益(S21)较大的增益有助于减小后级电路噪声的影响，但会引起线性度的恶化– 输入输出匹配(S11, S22)决定输入输出端的射频滤波器频响– 反向隔离(S12)– 线性度(IIP3， P1dB)未经滤除的干扰信号可通过互调(Intermodulation) 等方式使接收质量降低
上传时间： 2013-11-20
上传用户：xaijhqx
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
