本指南讨论最基本的DAC架构：“串”DAC和“温度计”DAC。串DAC的起源与开尔文爵士有 关，他于19世纪中叶发明了开尔文分压器。串DAC在当今颇受欢迎，特别是在典型分辨率 为6到8位的数字电位计等应用中。温度计DAC则相对独立于代码相关的开关毛刺，因而是 低失真分段DAC和流水线式ADC的常用构建模块。
上传时间： 2013-10-14
上传用户：zhqzal1014
ADC需要FFT处理器来评估频谱纯度，DAC则不同，利用传统的模拟频谱分析仪就能直接 研究它所产生的模拟输出。DAC评估的挑战在于要产生从单音正弦波到复杂宽带CDMA信 号的各种数字输入。数字正弦波可以利用直接数字频率合成技术来产生，但更复杂的数字 信号则需要利用更精密、更昂贵的字发生器来产生。 评估高速DAC时，最重要的交流性能指标包括：建立时间、毛刺脉冲面积、失真、无杂散 动态范围(SFDR)和信噪比(SNR)。本文首先讨论时域指标，然后讨论频域指标。
上传时间： 2013-10-27
上传用户：Vici
介绍了一款不要求负参考电压 (VREF) 的电流源 DAC/运算放大器接口。尽管该建议电路设计提供了一款较好的有效解决方案，但必须注意的是：如果 DAC 的最大兼容电压作为运算放大器输入 (VDAC+) 正端的设计目标，则负端 (VDAC–) 的 DAC 电压将会违反最大兼容输出电压，因为存在最初并不那么明显的偏置。下面的讨论，将对出现这种偏置的原因进行解释，并提出一种解决问题的简单方法。之后，我们将讨论在 DAC 和运算放大器之间插入一个滤波器的方法。
上传时间： 2013-10-22
上传用户：gut1234567
图1所示电路采用digiPOT+系列数字电位计AD5292、双通道运算放大器ADA4091-2和基准电压源ADR512，提供一种低成本、高电压、单极性DAC。该电路提供10位分辨率，输出电压范围为0 V至30 V，能够提供最高±20 mA的输出电流。AD5292可以通过SPI兼容型串行接口编程。
上传时间： 2013-11-23
上传用户：yuhaihua_tony
CS4398的DAC原理图
上传时间： 2013-10-24
上传用户：zoudejile
Abstract: This application note describes how sampling clock jitter (time interval error or "TIE jitter") affectsthe performance of delta-sigma digital-to-analog converters (DACs). New insights explain the importanceof separately specifying low-frequency (< 2x passband frequency) and high-frequency or wideband (> 2xpassband frequency) jitter tolerance in these devices. The article also provides an application example ofa simple highly jittered cycle-skipped sampling clock and describes a method for generating a properbroadband jittered clock. The document then goes on to compare Maxim's audio DAC jitter tolerance tocompetitor audio DACs. Maxim's exceptionally high jitter tolerance allows very simple and low-cost sampleclock implementations.
上传时间： 2013-10-25
上传用户：banyou
TLV5616 12 位 3微秒 DAC 串行输入可编程设置时间 功耗
上传时间： 2013-11-02
上传用户：xinyuzhiqiwuwu
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间： 2013-11-13
上传用户：ca05991270
Abstract: This article discusses application circuits for Maxim force/sense digital-to-analog converters (DACs). Applications include:selectable fixed-gain DAC, programmable gain DAC, photodiode bias control, amperometric sensor control, digitally programmablecurrent source, Kelvin load sensing, temperature sensing, and high current DAC output. A brief description of the various DAC outputconfigurations is also given.
标签： DAC
上传时间： 2013-11-04
上传用户：youmo81
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上传时间： 2013-10-17
上传用户：sjb555
