随着电信数据传输对速率和带宽的要求变得越来越迫切,原有建成的网络是基于话音传输业务的网络,已不能适应当前的需求.而建设新的宽带网络需要相当大的投资且建设工期长,无法满足特定客户对高速数据传输的近期需求.反向复用技术是把一个单一的高速数据流在发送端拆散并放在两个或者多个低速数据链路上进行传输,在接收端再还原为高速数据流.该文提出一种基于FPGA的多路E1反向复用传输芯片的设计方案,使用四个E1构成高速数据的透明传输通道,支持E1线路间最大相对延迟64ms,通过链路容量调整机制,可以动态添加或删除某条E1链路,实现灵活、高效的利用现有网络实现视频、数据等高速数据的传输,能够节省带宽资源,降低成本,满足客户的需求.系统分为发送和接收两部分.发送电路实现四路E1的成帧操作,数据拆分采用线路循环与帧间插相结合的方法,A路插满一帧(30时隙)后,转入B路E1间插数据,依此类推,循环间插所有的数据.接收电路进行HDB3解码,帧同步定位(子帧同步和复帧同步),线路延迟判断,FIFO和SDRAM实现多路数据的对齐,最后按照约定的高速数据流的帧格式输出数据.整个数字电路采用Verilog硬件描述语言设计,通过前仿真和后仿真的验证.以30万门的FPGA器件作为硬件实现,经过综合和布线,特别是写约束和增量布线手动调整电路的布局,降低关键路径延时,最终满足设计要求.
上传时间： 2013-07-16
上传用户：asdkin
本文档是华为的内部培训教材，关于高速数字电路的设计。
上传时间： 2013-08-06
上传用户：ccsdebug
高速数字电路设计。第一章 互连的重要性，第二章 理想传输线构造，第三章 串扰，第四章 非理想连接问题，第五章 连接器，过孔和封装
上传时间： 2013-04-24
上传用户：zhanditian
高速数字电路设计，实用
上传时间： 2013-10-10
上传用户：kelimu
华为《高速数字电路设计教材》
上传时间： 2014-12-23
上传用户：frank1234
高速数字系统设计下载pdf:High-Speed Digital SystemDesign—A Handbook ofInterconnect Theory and DesignPracticesStephen H. HallGarrett W. HallJames A. McCallA Wiley-Interscience Publication JOHN WILEY & SONS, INC.New York • Chichester • Weinheim • Brisbane • Singapore • TorontoCopyright © 2000 by John Wiley & Sons, Inc.speeddigital systems at the platform level. The book walks the reader through everyrequired concept, from basic transmission line theory to digital timing analysis, high-speedmeasurement techniques, as well as many other topics. In doing so, a unique balancebetween theory and practical applications is achieved that will allow the reader not only tounderstand the nature of the problem, but also provide practical guidance to the solution.The level of theoretical understanding is such that the reader will be equipped to see beyondthe immediate practical application and solve problems not contained within these pages.Much of the information in this book has not been needed in past digital designs but isabsolutely necessary today. Most of the information covered here is not covered in standardcollege curricula, at least not in its focus on digital design, which is arguably one of the mostsignificant industries in electrical engineering.The focus of this book is on the design of robust high-volume, high-speed digital productssuch as computer systems, with particular attention paid to computer busses. However, thetheory presented is applicable to any high-speed digital system. All of the techniquescovered in this book have been applied in industry to actual digital products that have beensuccessfully produced and sold in high volume.Practicing engineers and graduate and undergraduate students who have completed basicelectromagnetic or microwave design classes are equipped to fully comprehend the theorypresented in this book. At a practical level, however, basic circuit theory is all thebackground required to apply the formulas in this book.
上传时间： 2013-10-26
上传用户：缥缈
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
二: 普通计算器的设计说明: 1 普通计算器的主要功能(普通计算与逆波兰计算): 1.1主要功能: 包括 a普通加减乘除运算及带括号的运算 b各类三角与反三角运算（可实现角度与弧度的切换） c逻辑运算， d阶乘与分解质因数等 e各种复杂物理常数的记忆功能 f对运算过程的中间变量及上一次运算结果的储存. G 定积分计算器（只要输入表达式以及上下限就能将积分结果输出） H 可编程计算器（只要输入带变量的表达式后，再输入相应的变量的值就能得到相应的结果） I 二进制及八进制的计算器 j十六进制转化为十进制的功能。 *k (附带各种进制间的转化器)。 L帮助与阶乘等附属功能
上传时间： 2013-11-26
上传用户：yzy6007
最新delphi2005的b/s程序设计
上传时间： 2015-02-16
上传用户：redmoons
企业内部办公管理信息系统 （一个用ASP开发的基于B/S方式的毕业设计）
上传时间： 2013-12-13
上传用户：ynwbosss
