一般指连接交流电源的线圈称之为「一次线圈」(Primamary coil)；而跨于此线圈的电压称之为「一次电压」。在二次线圈的感应电压可能大于或小于一次电压，是由一次线圈与二次线圈问的「匝数比」所决定的。因此，变压器区分为升压与降压变压器两种。
标签： 变压器
上传时间： 2013-12-28
上传用户：gxmm
DC/DC 升压IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上传时间： 2013-11-07
上传用户：3294322651
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
Alkaline batteries are convenient because they’re easy tofi nd and relatively inexpensive, making them the powersource of choice for portable instruments and devicesused for outdoor recreation. Their long shelf life alsomakes them an excellent choice for emergency equipmentthat may see infrequent use but must be ready to go on amoment’s notice. It is important that the DC/DC convertersin portable devices operate over the widest possiblebattery voltage range to extend battery run time, and thussave the user from frequent battery replacement.
上传时间： 2014-12-24
上传用户：569342831
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
DC-link Automotive: MKP1849 (Customized)电动汽车电驱直流母线电容（顾客订制品）MKP1849系列.MKP1849-可集成母线排，大大降低了寄生电感，提高了系统稳定性。
上传时间： 2013-10-13
上传用户：nanfeicui
交一直一交变频器的中间直流环节如果是用大电容平波通常称为电压源型变频器。如果分开来称呼，则其后端逆变器部分叫电压源逆变器(VSI)，产品GB和IEC标准也是这种称呼。其前端整流部分对电网而言是— 个谐波源，也就叫电压型谐波源。与此相对照，交一直一交变频器的中间直流环节如果用大电感平波就分别称为电流源型变频器、电流源逆变器(CSD、电流源型谐波源。之所以要特别区分变频器为电压源和电流源两大类是因为他们的交流输入电流波形和变频后输出的交流电压和交流电流的波形及性能都有很大的不同。
上传时间： 2013-11-03
上传用户：xitai
摘 要:根据新型LCL谐振软开关弧焊逆变电源主电路原理,对这种弧焊电源进行了设计,并对电路中主要参数予以了确定。其内容包括:逆变电源输出电流Io及空载电压的计算、串联谐振电感Ls、电容Cs的参数选择、IGBT缓冲电容的参数选择。根据设计的电源参数,对研制的焊接电源进行试验。试验表明,该电源能够较好地实现软开关。从而证明该设计是合理的、有效的。关键词:谐振软开关;弧焊逆变;电源设计;参数选择
上传时间： 2013-11-16
上传用户：shaoyun666
简易负离子发生器负离子增加，对人有催眠、止汗、镇痛、增进食欲，使人精神爽快，消除疲劳的作用。图1是负离子发生器电路图。220V交流市电经D1整流后向C3和C2充电，当C2充电至氖泡导通并触发SCR导通时，C3经SCR、B的L1放电，经B感应升压后，由D2反向整流得8kV直流高压使发生器M的分子电离而产生负离子。调整R3的阻值可以改变触发频率和输出电压。调整时必须注意安全，更换元件需拨下电源插头
标签： 负离子发生器
上传时间： 2013-10-29
上传用户：731140412
超高压发生器输出几十千伏超高压、应用负粒子、点火、臭氧。简易超高压发生器，图1-1的电路可输出几十千伏超高压。当接通电源时，电源经R向C2充电至2CTS导通，即触发SCR导通。原来C被电源充满的电荷立即经SCR放电，升压变压器T次级感应高压电。当用汽车点火线圈作升压器，电容C1容量为0.1uF时，空气火花间长度为12mm。空气的绝缘度是3KV/mm，所以对应的高压是36KV。本电路耗电约为1W。制作时请注意安全！
上传时间： 2014-12-24
上传用户：wli25203
