虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

电工<b>手册</b>

  • 新编电工常用计算手册

    《新编电工常用计算手册》。此书介绍了一些基本的电工计算应用。

    标签: 电工 计算手册

    上传时间: 2013-06-11

    上传用户:大三三

  • 2012TI杯陕西赛题B题--频率补偿电路

    2012TI杯陕西赛题H题,2012TI杯陕西赛题B题--频率补偿电路.

    标签: 2012 TI 频率补偿电路

    上传时间: 2013-10-07

    上传用户:ysystc670

  • 三极管代换手册下载

    三极管代换手册下载 前言 使用说明 三极管对照表 A B C D E F G H K L M …… 外形与管脚排列图

    标签: 三极管 代换手册

    上传时间: 2013-10-24

    上传用户:zjf3110

  • 煤矿电工手册第二册上2

    煤矿电工手册第二册上2

    标签: 电工手册

    上传时间: 2013-11-12

    上传用户:chongchong1234

  • PSHLY-B回路电阻测试仪

    PSHLY-B回路电阻测试仪介绍

    标签: PSHLY-B 回路 电阻测试仪

    上传时间: 2013-11-05

    上传用户:木子叶1

  • 基于单片机的数字化B超键盘设计

    针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS,提出一种PS2键盘的设计方法。基于W78E052D单片机,采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路,电位器位置信息以键盘扫描码序列形式发送,正交编码器信号通过XC9536XL转换为单片机可接收的中断信号,软件接收到中断信息后等效处理成按键。结果表明,在满足开机可设置BIOS同时,又可实现超声特有功能,不需要专门设计驱动程序,接口简单,成本低。 Abstract:  Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot, this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller,designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter, potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU, software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot, ultrasound specific functionality can be achieved at the same time, it does not require specially designed driver,the interface is simple and low cost.    

    标签: 单片机 B超 数字化 键盘设计

    上传时间: 2013-10-10

    上传用户:asdfasdfd

  • I/O 型单片机使用手册

    I/O 型单片机使用手册 目录 间接寻址寄存器 – IAR, IAR0, IAR1 .............................................35间接寻址指针 – MP, MP0, MP1 ......................................................35存储区指针 – BP .........................................................................36累加器 – ACC...................................................................................37程序计数器低字节寄存器 – PCL....................................................37表格寄存器 – TBLP,TBHP,TBLH....................................................37看门狗定时寄存器 – WDTS............................................................38状态寄存器 – STATUS.....................................................................38中断控制寄存器 – INTC,INTC0,INTC1 .........................................39定时/计数寄存器...............................................................................39输入/输出端口和控制寄存器...........................................................40UART 寄存器 .USR,UCR1,UCR2,TXR/RXR,BRG.......................40输入/输出端口..........................................................................................41上拉电阻............................................................................................41PA 口的唤醒......................................................................................41输入/输出端口控制寄存器...............................................................41引脚共享功能....................................................................................42编程注意事项....................................................................................45定时/计数器..............................................................................................46配置定时/计数器输入时钟源...........................................................47定时/计数寄存器 – TMR, TMR0,TMR0L/TMR0H,TMR1L/TMR1H,TMR2.....................................................................49定时/计数控制寄存器 – TMRC,TMR0C,TMR1C,TMR2C............50定时器模式........................................................................................53事件计数器模式................................................................................53脉冲宽度测量模式............................................................................54可编程分频器(PFD)和蜂鸣器的应用..............................................55预分频器(Prescaler)...........................................................................56输入/输出接口...................................................................................56编程注意事项....................................................................................57定时/计数器应用范例.......................................................................57中断............................................................................................................59中断寄存器........................................................................................59中断优先权........................................................................................62外部中断............................................................................................63定时/计数器中断...............................................................................64UART 中断........................................................................................64编程注意事项....................................................................................65复位和初始化............................................................................................66复位....................................................................................................66目录iii异步串行口——UART............................................................................74UART 特性..........................................................................................74UART 外部引脚..................................................................................74数据发送.............................................................................................75UART 状态控制寄存器......................................................................75波特率发生器.....................................................................................79UART 设置与控制..............................................................................81UART 发送器......................................................................................83UART 接收器......................................................................................84接收错误处理.....................................................................................85接收中断图解.....................................................................................86地址检测模式.....................................................................................86暂停模式下的UART 功能.................................................................87UART 应用范例.................................................................................87振荡器........................................................................................................89系统时钟配置....................................................................................89系统晶体/陶瓷振荡器.......................................................................89系统电阻电容振荡器........................................................................90内部系统电阻电容振荡器................................................................90RTC 振荡器........................................................................................91看门狗定时振荡器............................................................................91暂停和唤醒................................................................................................92暂停.....................................................................................................92进入暂停.............................................................................................92静态电流.............................................................................................92唤醒....................................................................................................92看门狗定时器............................................................................................94掩膜选项....................................................................................................96应用电路....................................................................................................97第二部份 程序语言.....................................................................99第二章 指令集介绍.................................................................................101指令集......................................................................................................101指令周期..........................................................................................101数据的传送......................................................................................101算术运算..........................................................................................102逻辑和移位运算..............................................................................102分支和控制的转换..........................................................................102位运算..............................................................................................102查表运算..........................................................................................103其它运算..........................................................................................103指令设定一览表......................................................................................104惯例..................................................................................................104I/O 型单片机使用手册iv第三章 指令定义.....................................................................................107第四章 汇编语言和编译器.....................................................................121常用符号..................................................................................................121语句语法..................................................................................................122名称..................................................................................................122操作项..............................................................................................122操作数项..........................................................................................122注解..................................................................................................122编译伪指令..............................................................................................123条件编译伪指令..............................................................................123文件控制伪指令..............................................................................124程序伪指令......................................................................................126数据定义伪指令..............................................................................130宏指令..............................................................................................132汇编语言指令..........................................................................................136名称..................................................................................................136助记符..............................................................................................136操作数、运算子和表达式..............................................................136其它..........................................................................................................139前置引用..........................................................................................139局部标号..........................................................................................139汇编语言保留字..............................................................................140编译器选项..............................................................................................141编译列表文件格式..................................................................................141源程序列表......................................................................................141编译总结..........................................................................................142其它..................................................................................................142第三部份 开发工具................................................................... 145第五章 单片机开发工具.........................................................................147HT-IDE 集成开发环境............................................................................147盛群单片机仿真器(HT-ICE) ..................................................................149HT-ICE 接口卡.................................................................................149OTP 烧写器.....................................................................................149OTP 适配卡.....................................................................................149系统配置..................................................................................................150HT-ICE 接口卡设置........................................................................151安装..........................................................................................................153系统要求..........................................................................................153硬件安装..........................................................................................153软件安装..........................................................................................154目录v第六章 快速开始.....................................................................................159步骤一:建立一个新项目..............................................................159步骤二:将源程序文件加到项目中..............................................159步骤三:编译项目..........................................................................159步骤四:烧写OTP 单片机.............................................................160步骤五:传送程序与掩膜选项单至Holtek ..................................160附录............................................................................................... 161附录A 特性曲线图...................................................................................163附录B 封装信息.......................................................................................173

    标签: 单片机 使用手册

    上传时间: 2013-10-18

    上传用户:blacklee

  • TKS仿真器B系列快速入门

    TKS仿真器B系列快速入门

    标签: TKS 仿真器 快速入门

    上传时间: 2013-10-31

    上传用户:aix008

  • 袖珍电工手册

    袖珍电工手册

    标签: 电工手册

    上传时间: 2013-11-21

    上传用户:缥缈

  • 一个简单好用的B+树算法实现

    一个简单好用的B+树算法实现

    标签: 算法

    上传时间: 2015-01-04

    上传用户:缥缈