在实际操作中，还有一种非常简单适用的焊接方法：就是在 D15 两端的 5~10 脚焊接在一起做公共地，红、绿、蓝的屏蔽线绞在一起接到公共地上； 1 、 2 、 3 脚接红、绿、蓝的芯线； 13 接黄线；14 接白线； 外层屏蔽压接到 D15 插头端壳，褐线和黑线不用接，但是要剪齐，以防和其他线串接。
上传时间： 2013-11-13
上传用户：xuanchangri
介绍的是51单片机实现mudbus的从机程序
上传时间： 2013-10-17
上传用户：123454
为了提高PCB板制作的效率，改变传统的化学腐蚀制板工艺，使用机械仿形铣制作电路板的方法，设计了以ATMEGA16单片机为核心部件的PCB板雕刻机控制系统。其中包括PCB雕刻机的基本功能、主要硬件电路设计和软件的实现流程，并给出了相关设计电路。重点分析了雕刻机步进电机的驱动电路以及主轴电机的驱动电路，该雕刻机经实际运行，系统工作良好，可有效提高PCB板的制作效率。 Abstract: In order to improve the efficiency of production of PCB board and change the traditional chemical etching plates， using of mechanical copying milling method makes circuit boards，this paper introduces the PCB engraving machine control system used ATMEGA16 microcomputer as the core components. It includes basic function， the hardware circuit design and software realization process， and gives the corresponding circuit design.It analyses the drive circuit of engrawing machine stepper motor and spindle motor in detail. This engraving machine by practical operation， the system works well， which can effectively improve the production efficiency of PCB board.
上传时间： 2013-10-17
上传用户：liangliang123
学习单片机离不开实验，以往单片机的实验往往依赖于仿真机和单片机学习系统，价格 昂贵，至使学习单片机的门槛很高，很多人不能跨入单片机学习的大门。近年来，随着FLASH 型单片机的广泛应用，采用软件模拟加写片验证成为一种经济实用的实验方法，尤其是随着 单片机技术的发展，很多单片机都具有了ISP 功能，只要一根下载线即可以编程。STC 单片 机更是将其ISP 功能发挥极致，只要有RS232 接口，不需任何其他电路即可实现ISP 功能。。 多年前，本网站为单片机爱好者设计了实验电路板，并公开了全部的软、硬件资料，广 受爱好者欢迎，很多人使用这块实验电路板学习并由此入门，同时网络上也出现了很多同类 功能的实验电路板，为广大爱好者学习单片机创造了良好的条件。
上传时间： 2014-11-29
上传用户：540750247
详细介绍工控软件组态王与单片机多机串口通讯的设计原理。分析组态王提供的直接与单片机串口通信方法的优点，给出系统基于RS-485总线传输的接口电路原理图。根据组态王提供的通讯协议和单片机多机串口通讯的原理，给出程序设计流程与思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上传时间： 2013-12-19
上传用户：tecman
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
对于传统的跑步机无法联机组网，保存历史数据，实时调试等问题，介绍了一个由多台跑步机通过RS-232串行总线与上位机相连组成的跑步机联网系统。系统采用W77E58作为下位机核心控制器件，它具有双串行通讯端口，其中一个串口用于与变频器通讯，另一个串口则与上位机相连，构成跑步机网络。 Abstract: The traditional running machine can not be connected to a network, saving historical data, real time debug etc.In this paper,a new network system which is composed of running machines connected by a RS-232 communication bus is introduced.In the system,W77E58 is used as a core control unit.W77E58 has two serial ports,one is connected to the inverter and the other is connected to the PC. Thus a network appears.
上传时间： 2014-12-27
上传用户：哇哇哇哇哇
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
AVRPRO烧录器，是针对ATMEL公司的90系列AVR精简指令单片机设计的专用烧录工具该产品只有软件部分，无需硬件支持，仅仅只需4根线，将计算机并口和用户板相连，这都是因为采用了ISP串行编程。软件支持擦、写、校验、写保护位以及批处理。使用极其方便。 该产品的最大优点有： 1． 使用串行编程，达到了在线编程，节省了购买万用编程器和适配器的费用（万用编程器需2千元左右，适配器需3、4百元，并各个芯片和封装需不同适配器）。用户板也无需在焊插座（带来可靠性下降），而且为软件升级带来了极大的便利。 2． 使用方便，无需硬件，给现场调试带来了极大的便利，不用再带笨重的编程器，而且为AVR单片机的使用上带来了方便。 3． 价格实在太便宜，为您省了不少钱。 硬件使用说明： 并口和用户板连接说明 并口2脚<―――>用户板单片机MOSI 并口3脚<―――>用户板单片机SCK 并口12脚<―――>用户板单片机MISO 并口25脚<―――>用户板单片机GND 软件使用说明： 软件名是AVRPRO.EXE，支持DOS,WIN9x，支持.hex（intel）格式，可直接运行AVRPRO.EXE，也可以键入AVRPRO.EXE 目录\文件名.HEX，直接运行时可进入菜单，可选择擦、写、校验、写保护位以及批处理。键入文件名时，软件运行批处理，自动完成擦、写、校验、写保护位
上传时间： 2014-12-27
上传用户：zhang97080564
针对当前安检力学试验机所能完成的试验种类单一、自动化程度低等问题，提出一种以ATmega128单片机为核心控制器的安检力学试验机的设计。详细阐述了该安检力学试验机各个组成部分的设计原理和方案，并且给出了各部分的软件设计思想和操作流程。经过大量测试试验表明：设计的安检力学试验机可以完成多达十余种的力学安检试验，完全符合相关国家标准，并且具有数据采集精度高、传输速度快、操作安全简便等特点，实现了安检设备的多功能化、数字化和自动化。 Abstract: Currently， many mechanical security testing machines have only one function. The degree of automation of them is low. To solve those problems， a new kind of mechanical security testing machine， using ATmega128 micro-controller as its core controller， has been advanced. It describes the components of the machine. The principles and the scheme in the designing processes are presented in detail， and the software architecture and the operation processes of each part are given. After having done many testing， we have reached the following conclusions: the mechanical security testing machine presented can do over ten mechanical security tests complying with related national standards. It has high data acquisition accuracy and high transmission speed. The operation of the machine is simple and safe. In general， this machine is a multi-functional， highly automatic， digitalized security testing device.
上传时间： 2013-11-05
上传用户：a67818601
