设计一种基于P89V51RD2的功率因数测量仪，采用光电隔离器和专用数码管驱动器。该测量仪是以增强型单片机P89V51RD2为核心，大大简化系统硬件设计。而软件部分采用模块化设计思想，采用中值滤波和小数补偿算法，实现功率因数的高精度测量。实验测试表明，该功率因数测量仪测量精度高，运行稳定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上传时间： 2014-12-27
上传用户：CHINA526
首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
应用德国Micronas公司的CDC3207G微控制器开发了一款汽车仪表板系统。详细地介绍了该系统的硬件原理，以及步进电机，音频控制，LCD显示，LED指示灯和报警灯等几个模块的实现方法。应用μC/OS-II实时操作系统开发软件。着重介绍了启动代码的设计和任务的规划。 Abstract: A dashboard system is developed by using CDC3207G microcontroller made by Micronas.The hardware of the sys-tem and the realization of the step motor module,audio module,LCD display and LED indicator and alarm module are ex-plained in detail.The μC/OS-II real-time operating system is used for the software development and the starting code design and the task planning is explained specifically.
上传时间： 2013-10-26
上传用户：x4587
介绍了一种基于C8051F020单片机的多路压力测量仪。该测量仪选用电阻应变式压力传感器采集压力信号，并经放大电路处理后送入C8051F020单片机，再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化，然后分别对数据进行存储和显示。该测量仪能测量6路压力信号，并且各测量点都能单独检测和设置。由于采用了C8051F020单片机，简化了硬件电路，增强了抗干扰能力，使得测量仪具有测量精度高，冲击小等特点。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上传时间： 2013-11-16
上传用户：yare
在工作控制和智能化仪表中，通常由微型计算机进行实时控制及实时数据处理。计算机所加工的信息总是数字量，而被控制或测量对象的有关参量往往是连续变化的模拟量，如温度、速度、压力等等，与此对应的电信号是模拟电信号。计算机要处理这种信号，首先必须将模拟量转换成数字量，这一转换过程就是“模/数转换（A/D）”
上传时间： 2013-10-24
上传用户：tzl1975
针对目前采用的热敏电阻测量方法，提出了采用单总线数字式温度传感器DS18B20和单片机组成的新型温度测量仪。介绍DS18B20的结构和工作原理，以及单总线工作原理，给出了由Mega8单片机和DS18B20构成的单总线温度测量仪的硬件电路及软件流程图。经试验基于单总线器件DS18B20的温度测量仪，具有测量准确、测温范围宽、体积小、控制方便等优点。 Abstract: This paper brings forward a new temperature meter composed of 1-Wire temperature sensor DS18B20 and MCU which has advantage of the thermistor. In the article, the DS18B20＇s structure and controlling principles are introduced and hardware circuit and software diagram of the temperature meter are given.After been tested,the temperature meter has the advantages of accurate measurement, wide temperature range, small volume and convenient controlling.
上传时间： 2013-10-31
上传用户：hzy5825468
介绍一种以MSP430单片机为基础的智能频率测量系统，采用硬件逻辑与软件指令相结合的方式控制闸门，实现0 MHz~10 MHz范围内无档切换的等精度测量。 Abstract: An intelligent frequency measurement system based on MSP430 singlechip is introduced. The system uses a way that can combine hardware logic and software instructions to contronl the strobe ,and completes the functions of equal precision in the range of 0MHz~10MHz without shifting
上传时间： 2013-10-28
上传用户：dbs012280
本文对激光扫描车身坐标测量系统的数据采集部分进行了深入研究，设计了基于“AVR+FIFO+CPLD”的数据采集及处理模块；解决了当多路信号有数据同时传输时，如何将数据完整地写入FIFO的问题，实现了数据的有效采集；编写了完整的CPLD控制程序和AVR数据采集程序，为准确测量待测点的坐标提供了可靠的数据来源。
上传时间： 2013-10-29
上传用户：asaqq
涡街流量计因其介质适应性强，无可动部件，结构简单、使用寿命长等诸多优点，在许多行业得到了广泛的应用。而在低流速下，涡街测量就凸显出了它的不足，涡街信号的信噪比很低，有用信号几乎被噪声淹没。普通的涡街流量计采用模拟信号处理方法，在正常流量范围内，涡街流量信号稳定、测量准确、实时性好；鉴于上述模拟涡街流量计具有的优势以及存在的不足，课题的目的是数字信号处理方法FFT应用于涡街流量仪表当中，采用双MSP430单片机的结构进行脉冲计频和FFT计算，并且实时进行脉冲输出及电流输出。使其具有测量下限低，抗干扰能力强，实时数字信号处理等特点。
上传时间： 2014-12-01
上传用户：wujijunshi
在现在的工业或实验室应用中， 对涡轮流量计的二次仪表提出了越来越多的要求， 准确度高、抗干扰能力强、集成度高、接口齐全、使用方便等都成了选购的主要考虑因素。本文描述了一种基于单片机的可适用于工业和实验室的高精度涡轮流量计二次仪表的设计过程
上传时间： 2013-11-22
上传用户：panpanpan
