为了实现对矿山生产过程中三维定位和灾害预警监测，设计了一种基于RFID和无线传感的矿山实时定位预警系统，硬件包括无线射频标识模块、实时三维定位模块、监测数据采集与分析模块、灾害预警模块、灾害分析模块和地面远程控制主机。实际应用表明，该系统平台铺设灵活性强，监控范围广泛，可以三维全方位监控，有效提高矿山安全监测效率。
上传时间： 2013-11-23
上传用户：363186
采用RFID（射频识别）芯片IA4420设计了一款主动式应答器，主要应用于矿井安全生产管理。其工作中心频率为905 MHz，数据通信的核心部分是印刷偶极子天线，从仿真结果来看：其相对带宽约为40%，增益约为4.236 dB，输入阻抗接近纯电阻 50 Ω，性能参数较好。
上传时间： 2013-11-12
上传用户：caiguoqing
给出一种实时互锁式无线抢答手柄的设计应用实例，使无线抢答器的死区时间由通常的40 ms锐减为40 μs。其基本思路是：在每只抢答手柄中增加一片射频接收模块和一个电子开关、配以相应的附属电路，使该电子开关受控于接收模块输出信号的有无，并决定手柄中的射频发射模块是否通电工作，从而实现各抢答手柄之间的实时互锁。只有首先被按下抢答按键的手柄，才有可能向外发送编码射频。持有该手柄的选手即为抢答成功者。
上传时间： 2013-11-10
上传用户：JGR2013
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
上传时间： 2013-10-23
上传用户：685
Abstract: This application note illustrates the flexibility of the MAX7060 ASK/FSK transmitter. While the currently available evaluationkit (EV kit) has been optimized for the device's use in a specific frequency band (i.e., 288MHz to 390MHz), this document addresseshow the EV kit circuitry can be modified for improved operation at 433.92MHz, a frequency commonly used in Europe. Twoalternative match and filter configurations are presented: one for optimizing drain efficiency, the other for achieving higher transmitpower. Features and capabilities of earlier Maxim industrial, scientific, and medical radio-frequency (ISM-RF) transmitters areprovided, allowing comparison of the MAX7060 to its predecessors. Several design guidelines and cautions for using the MAX7060are discussed.
上传时间： 2013-11-14
上传用户：swaylong
提出了一种基于PIC16F877A微控制器和CC2500射频收发器芯片的低功耗、低成本RFID（Radio Frequency Identification， 无线射频识别）局域定位系统设计方法，介绍了系统的定位工作原理、主要硬件电路模块及定位算法的设计和实现。采用基于序列号对时隙数运算的排序算法有效解决了多标签识别碰撞的问题，基于射频辐射强度（Received Signal Strength Indication， RSSI）和圆周定位算法实现了基于RFID多标签系统的平面定位。实验测试表明，这种射频定位方法能够实现一定精度下的无线局域定位的功能。
上传时间： 2013-11-06
上传用户：weareno2
在3.84 Mcps条件下，考虑到处理增益后，满足灵敏度要求所允许的总噪声。这个总噪声包括输入热噪声kTB和系统引入的噪声NF。
上传时间： 2013-12-29
上传用户：妄想演绎师
ADS – Advanced Design System，由美国Agilent 公司推出的微波电路和通信系统仿真软件，是当今业界最流行的微波射频电路、通信系统、RFIC 设计软件.
上传时间： 2013-10-19
上传用户：维子哥哥
为了实现嵌入式手持终端系统的功耗低、体积小、性能稳定的需求，以TI公司的MSP430F449的16位低功耗微控制器为中央处理单元，Semtech公司的SX1233为射频收发单元，设计了一种能广泛应用于餐饮、物流、无线抄表等领域的低成本、超低功耗的无线手持终端设备。分析了系统的功耗和编程特点，给出了系统软件的设计方案。实测结果表明，所设计的无线手持终端设备性能稳定、灵活可调，达到了设计要求。
上传时间： 2013-10-18
上传用户：SimonQQ
为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
