HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
标签： C8051F020
上传时间： 2013-10-12
上传用户：lalalal
常用PIC系列产品特性一览表 器件 存储器 类型 字数 EEPROM 数据 存储器 RAM I/O 引脚数 ADC （-Bit） 比较 器 运 放 定时器/WDT 串行接口 最高 速度 MHz 封装 PDIP /SOIC ICSP CCP / ECCP 输出电流 (per I/O) 振荡器 频率 (MHz) 参考 电压 VREF LCD PWM 堆栈 深度 High Voltage Wakeup On Change PIC16C432 OTP 2048x14 128 12 2 1-8bit/1-WDT 20 20 √ 25 mA 4 0 0 PIC16C433 OTP 2048x14 128 6 4/8 1-8bit/1-WDT 10 18 √ 25 mA 0 0 PIC16C505 OTP 1024x12 72 12 1-8bit/1-WDT 20 14 √ 25 mA 4 0 0 PIC16C54 OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54A OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54C OTP 512x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C55 OTP 512x12 24 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C554 OTP 512x14 80 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C558 OTP 2048x14 128 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C55A OTP 512x12 24 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C56 OTP 1024x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C56A OTP 1024x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C57 OTP 2048x12 72 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C57C OTP 2048x12 72 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C58B OTP 2048x12 73 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C620 OTP 512x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C620A OTP 512x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C621 OTP 1024x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C621A OTP 1024x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C622 OTP 2048x14 128 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C622A OTP 2048x14 128 13 2 1-8bit/1-WDT 40 18/20/40 √ 25 mA √ 0 0 PIC16C62A OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C/ SPI 20 28/ √ 1 25 mA 1 0 0 PIC16C62B OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C /SPI 20 28 √ 1 25 mA 1 0 0 PIC16C63 OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 28 √ 2 25 mA 2 0 0 PIC16C63A OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C642 OTP 4096x14 176 22 2 1-8bit/1-WDT 20 28 √ 25 mA √ 0 0 PIC16C64A OTP 2048x14 128 33 2-8bit/1-16bit/1-WDT I²C /SPI 20 40/44 √ 1 25 mA 1 0 0 PIC16C65A OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C65B OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C66 OTP 8192x14 368 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C662 OTP 4096x14 176 33 2 1-8bit/1-WDT 20 40/44 √ 25 mA √ 0 0 PIC16C67 OTP 8192x14 368 33 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C71 OTP 1024x14 36 13 4/8 1-8bit/1-WDT 20 18 √ 25 mA 0 0 PIC16C710 OTP 512x14 36 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C711 OTP 1024x14 68 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA
上传时间： 2013-10-12
上传用户：xjy441694216
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
设计一种基于AT89C52的语音录放系统，利用单片机、ISD2560语音录放器件、麦克风、扬声器等元器件实现硬件电路的设计，并利用C51高级语言设计ISD2560器件控制字的写入和定时中断程序。经软硬件调试，结果表明该系统录放效果良好，具有一定的工程实用价值。 Abstract: Voice recording and playback system based on AT89C52is designed in this paper.Using the single-chip microcomputer，voice recording and playback chip ISD2560，microphone and speaker to realize the hardware circuit design.Writing ISD2560control words and timing interrupt procedures are designed by C51advanced language.Through the hardware and software test,voice recording and playback system play better voice,and this system has some engineering practical values.
上传时间： 2013-10-20
上传用户：ywcftc277
介绍基于ISA总线与KH-9300的数据采集板卡的设置，详细说明8254定时计数器及8259中断控制器的结构特点、工作方式、控制字等，探讨中断类型、中断处理程序、中断矢量表及其填写。重点讲述使用TorboC编写中断服务程序的方法，应注意的主要问题及程序测试的结果。 Abstract: The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
上传时间： 2013-11-14
上传用户：qq527891923
概述 BL22P02是一款低功耗8位OTP型微控制器单元（MCU），适用于各类小家电控制。 主要特点 8位CISC结构CPU（Motorola HC05兼容）17个通用IO口8位实时定时器/计数器，其信号源和触发沿可由软件设定，可设置溢出中断7路键盘中断（KBI）2路外中断（INT）振荡模式晶振：32K晶振：432K-8MHz内部RC：2MHz@5V、4MHz@5V、6MHz@5V外接电阻低功耗设计（静态功耗<1uA@5V）内部自振式看门狗计数器（WDT）64byteRAM2K*8bitOTPROM串行烧写接口电路程序加密功能工作电压2.0-5.5V@（432K-4M）2.7-5.5V@（432K-8M）封装形式：DIP20、SOP20、DIP18、SOP18、DIP16、SOP16、DIP14、SOP14、DIP8、SOP8
上传时间： 2013-10-15
上传用户：佳期如梦
在开放式数控系统结构模型的基础上，研究了基于ISA总线的DSP通信控制原理。采用中断方式完成了PC机和DSP之间的通信。介绍了以DriverWorks为工具开发ISA设备WDM驱动程序的方法，探讨了中断处理、驱动程序与应用程序之间的通信,简要说明了驱动程序的安装与调试。通过调试,系统设计运行稳定。 Abstract: The ISA bus and DSP correspondence control principle is investigated in the basis of the existing open architecture numerical control system.The interrupt method is used to realize the communication between PC and DSP based on the ISA bus.The methods of WDM driver exploitation for ISA device using Driver Works are introduced.The main process of driver program and the keys such as handle interrupt and the communication between the drivers and application are presented.And how to debug and install the drive is explained.
上传时间： 2013-11-04
上传用户：kang1923
C8051F020单片机通过SPI接口驱动四线电阻式触摸屏控制器TSC2046，利用中断方式驱动TSC2046设计软件。介绍了触摸屏的工作原理、TSC2046工作方式以及典型应用电路。 Abstract: The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen controller. The TSC2046 is controlled by interrupt mode, the? operation principle of touch screen is introduced. The operation mode of TSC2046 and typical application circuit are also discussed.
上传时间： 2014-12-27
上传用户：hwl453472107
介绍了一种基于AT89S52微处理器、键控显示模式、多汉字显示的显示模块设计方法。对AT89S52的内部功能及使用高128字节RAM时的寻址方式进行说明。给出了四汉字显示模块的硬件电路原理图、主程序流程图以及中断显示流程图。 Abstract: The design method of display module base on the AT89S52 microcontroller,display mode controlled by keyboard and? showing several Chinese characterses are introduced in the paper.The internal function and the addressing mode for the high 128B RAM of the AT89S52 are explained.The basic circuit diagram,the main program flow chart and the display interrupt flow chart of four Chinese characterses display module are also given.
上传时间： 2014-01-23
上传用户：咔乐坞
利用AT89C51型单片机定时和中断功能，配以LM386型音频功率放大器，构成了作息号音自动播放器，为学校和机关管理提供方便。 Abstract: Using timing and interrupt function of the AT89C51 single-chip microcomputer and the LM386 audio power amplifier.It is constituted the automatic bugle player.This player facilitates the institution and the school daily management.
上传时间： 2013-10-10
上传用户：wivai
