In this paper, we discuss efficient coding and design styles using verilog. This can beimmensely helpful for any digital designer initiating designs. Here, we address different problems rangingfrom RTL-Gate Level SimulATion mismatch to race conditions in writing behavioral models. All theseproblems are accompanied by an example to have a better idea, and these can be taken care off if thesecoding guidelines are followed. Discussion of all the techniques is beyond the scope of this paper, however,here we try to cover a few of them.
标签： Efficient Verilog Digital Coding
上传时间： 2013-11-23
上传用户：我干你啊
The LogiCORE™ GTP Wizard automates the task of creating HDL wrappers to configure the high-speed serial GTP transceivers in Virtex™-5 LXT and SXT devices. The menu-driven interface allows one or more GTP transceivers to be configured using pre-definedtemplates for popular industry standards, or from scratch, to support a wide variety of custom protocols.The Wizard produces a wrapper, an example design, and a testbench for rapid integration and verification of the serial interface with your custom function Features• Creates customized HDL wrappers to configureVirtex-5 RocketIO™ GTP transceivers• Users can configure Virtex-5 GTP transceivers toconform to industry standard protocols usingpredefined templates, or tailor the templates forcustom protocols• Included protocol templates provide support for thefollowing specifications: Aurora, CPRI, FibreChannel 1x, Gigabit Ethernet, HD-SDI, OBSAI,OC3, OC12, OC48, PCI Express® (PCIe®), SATA,SATA II, and XAUI• Automatically configures analog settings• Each custom wrapper includes example design, testbench; and both implementation and SimulATion scripts
标签： Transceiver Virtex Wizar GTP
上传时间： 2013-10-20
上传用户：dave520l
本文利用Verilog HDL 语言自顶向下的设计方法设计多功能数字钟，突出了其作为硬件描述语言的良好的可读性、可移植性和易理解等优点，并通过Altera QuartusⅡ 4.1 和ModelSim SE 6.0 完成综合、仿真。此程序通过下载到FPGA 芯片后，可应用于实际的数字钟显示中。 关键词：Verilog HDL；硬件描述语言；FPGA Abstract: In this paper, the process of designing multifunctional digital clock by the Verilog HDL top-down design method is presented, which has shown the readability, portability and easily understanding of Verilog HDL as a hard description language. Circuit synthesis and SimulATion are performed by Altera QuartusⅡ 4.1 and ModelSim SE 6.0. The program can be used in the truly digital clock display by downloading to the FPGA chip. Keywords: Verilog HDL；hardware description language；FPGA
上传时间： 2013-11-10
上传用户：hz07104032
Pspice教程课程内容：在这个教程中，我们没有提到关于网络表中的Pspice 的网络表文件输出，有关内容将会在后面提到!而且我想对大家提个建议：就是我们不要只看波形好不好，而是要学会分析，分析不是分析的波形，而是学会分析数据，找出自己设计中出现的问题!有时候大家可能会看到，其实电路并没有错，只是有时候我们的仿真设置出了问题，需要修改。有时候是电路的参数设计的不合理，也可能导致一些莫明的错误!我觉得大家做一个分析后自己看看OutFile文件!点,就可以看到详细的情况了!基本的分析内容：1．直流分析2．交流分析3．参数分析4．瞬态分析进阶分析内容：1． 最坏情况分析.2． 蒙特卡洛分析3． 温度分析4． 噪声分析5． 傅利叶分析6． 静态直注工作点分析数字电路设计部分浅谈附录A: 关于SimulATion Setting的简介附录B： 关于测量函数的简介附录C：关于信号源的简介
上传时间： 2013-10-14
上传用户：31633073
解压密码：www.elecfans.com 随着微电子技术的迅速发展以及集成电路规模不断提高，对电路性能的设计 要求越来越严格，这势必对用于大规模集成电路设计的EDA 工具提出越来越高的 要求。自1972 年美国加利福尼亚大学柏克莱分校电机工程和计算机科学系开发 的用于集成电路性能分析的电路模拟程序SPICE（SimulATion Program with IC Emphasis）诞生以来，为适应现代微电子工业的发展，各种用于集成电路设计的 电路模拟分析工具不断涌现。HSPICE 是Meta-Software 公司为集成电路设计中 的稳态分析，瞬态分析和频域分析等电路性能的模拟分析而开发的一个商业化通 用电路模拟程序，它在柏克莱的SPICE（1972 年推出），MicroSim公司的PSPICE （1984 年推出）以及其它电路分析软件的基础上，又加入了一些新的功能，经 过不断的改进，目前已被许多公司、大学和研究开发机构广泛应用。HSPICE 可 与许多主要的EDA 设计工具，诸如Candence,Workview 等兼容，能提供许多重要 的针对集成电路性能的电路仿真和设计结果。采用HSPICE 软件可以在直流到高 于100MHz 的微波频率范围内对电路作精确的仿真、分析和优化。在实际应用中， HSPICE能提供关键性的电路模拟和设计方案，并且应用HSPICE进行电路模拟时， 其电路规模仅取决于用户计算机的实际存储器容量。 The HSPICE Integrator Program enables qualified EDA vendors to integrate their products with the de facto standard HSPICE simulator, HSPICE RF simulator, and WaveView Analyzer™. In addition, qualified HSPICE Integrator Program members have access to HSPICE integrator application programming interfaces (APIs). Collaboration between HSPICE Integrator Program members will enable customers to achieve more thorough design verification in a shorter period of time from the improvements offered by inter-company EDA design solutions.
上传时间： 2013-10-18
上传用户：s363994250
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and SimulATion of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2014-01-24
上传用户：s363994250
为了提高直接转矩控制（DTC）系统定子磁链估计精度，降低电流、电压测量的随机误差，提出了一种基于扩展卡尔曼滤波（EKF）实现异步电机转子位置和速度估计的方法。扩展卡尔曼滤波器是建立在基于旋转坐标系下由定子电流、电压、转子转速和其它电机参量所构成的电机模型上，将定子电流、定子磁链、转速和转子角位置作为状态变量，定子电压为输入变量，定子电流为输出变量，通过对磁链和转速的闭环控制提高定子磁链的估计精度，实现了异步电机的无速度传感器直接转矩控制策略，仿真结果验证了该方法的可行性,提高了直接转矩的控制性能。 Abstract: In order to improve the Direct Torque Control（DTC） system of stator flux estimation accuracy and reduce the current， voltage measurement of random error， a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters （state vector: stator current， stator flux linkage， rotor angular speed and position； input: stator voltage； output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The SimulATion results show it is efficient and improves the control performance.
上传时间： 2015-01-02
上传用户：qingdou
在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力，可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明，电路性能指标达到了设计要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final SimulATion results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上传时间： 2014-01-21
上传用户：shen007yue
TOYFDTD1 is a stripped-down minimalist, 3D FDTD code demonstrating the basic tasks in implementing a simple 3D FDTD SimulATion. An idealized rectangular waveguide is modeled by treating the interior of the mesh as free space and enforcing PEC conditions on the faces of the mesh. A simplified plane wave source is inserted at one end. First released 12 April 1999. Version 1.03 released 2 December 1999.
标签： demonstrating stripped-down implementing minimalist
上传时间： 2013-12-21
上传用户：无聊来刷下
股票交易模拟器 A Stock Exchange simulator to show timers and randon number generators work together. A cool SimulATion for anyone who might think about playing the stocks and spending money and get a general idea how the system works.
标签： generators simulator Exchange together
上传时间： 2015-04-13
上传用户：爱死爱死
