A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.
上传时间： 2013-10-31
上传用户：masochism
Abstract: The MAX9930–MAX9933 family of RF controllers and detector can be used in a wide variety of applications. Anideal application is cable television (CATV) over fiber, where either a RF controller or a RF detector controls the gain of atransimpedance amplifier (TIA). This application note shows how the MAX9930 (RF controller) can be used as either theRF controller or detector.
上传时间： 2013-10-11
上传用户：Pzj
Abstract: The DS4830 optical microcontroller's analog-to-digital converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
上传时间： 2014-12-23
上传用户：萍水相逢
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上传时间： 2014-12-23
上传用户：781354052
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上传时间： 2013-10-17
上传用户：sjb555
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
标签： Transimpedance Stabilize Amplifier Your
上传时间： 2013-11-13
上传用户：daoyue
This application note provides a detailed description of themetastable behavior in PLDs from both circuit and statisticalviewpoints. Additionally, the information on the metastablecharacteristics of Cypress PLDs presented here can help youachieve any desired degree of reliability.
上传时间： 2013-10-23
上传用户：gtzj
Designers of signal receiver systems often need to performcascaded chain analysis of system performancefrom the antenna all the way to the ADC. Noise is a criticalparameter in the chain analysis because it limits theoverall sensitivity of the receiver. An application’s noiserequirement has a signifi cant infl uence on the systemtopology, since the choice of topology strives to optimizethe overall signal-to-noise ratio, dynamic range andseveral other parameters. One problem in noise calculationsis translating between the various units used by thecomponents in the chain: namely the RF, IF/baseband,and digital (ADC) sections of the circuit.
上传时间： 2014-12-05
上传用户：cylnpy
This application note features 8-, 10-, and 12-bit dataacquisition components in various circuit configurations.The circuits include battery monitoring, temperature sensing,isolated serial interfaces, and microprocessor andmicrocontroller serial and parallel interfaces. Also includedare voltage reference circuits (Application Note 42contains more voltage reference circuits).
上传时间： 2014-01-15
上传用户：zq70996813
The Reactor design pattern handles service requests that are delivered concurrently to an application by one or more clients. Each service in an application may consist of serveral methods and is represented by a separate event handler that is responsible for dispatching service-specific requests.
上传时间： 2013-10-15
上传用户：libinxny
