电源开发资料,能够使电源降压,输入在7--40V的范围,输出为5V
上传时间： 2013-12-27
上传用户：sssl
The ISL8540 is a step down DC/DC power switching regulator which accepts 9.0V to 40V input and provi
标签： Switching Regulator Power DC
上传时间： 2013-06-07
上传用户：shanml
●抗线路接反功能可在线路跨接出错时为技术员节省查找故障所消耗的大量时间； ●采用与 RS-485 相同的外引脚，无需重新设计电路板； ●总线引脚能承受 –35V 至 +40V 之间的故障，可为典型 24 Vac HVAC 电源最大限度地降低直接短路所造成的损害； ●多达 32 个节点的高输入阻抗可在统一网络上支持多节点，无需中继器，从而可降低系统成本
标签：
上传时间： 2013-06-22
上传用户：624971116
General Description The LM621 is a bipolar IC designed for commutation of brushless DC motors. The part is compatible with both three- and four-phase motors. It can directly drive the power switching devices used to drive the motor. The LM621 provides an adjustable dead-time circuit to eliminate ``shootthrough'' current spiking in the power switching circuitry. Operation is from a 5V supply, but output swings of up to 40V are accommodated. The part is packaged in an 18-pin, dual-in-line package.
上传时间： 2013-07-24
上传用户：sdq_123
PT4115是一款连续电感电流导通模式的降压恒流源，用于驱动一颗或者多颗串联LED。根据不同外部器件，芯片可以驱动高达数十瓦的LED。PT4115具有调光功能，通过DIM引脚实现模拟调光和宽范围PWM调光。当VDIM低于0.3V时，功率开关关断，芯片进入低功耗待机状态 主要技术参数 输入电压范围：6V to 40V 最大输出LED电流1.2A 5%的输出电流精度 高达97%的效率 极少的外部器件 复用DIM引脚进行LED开关、模拟调光和PWM调光 LED开路保护 LED过热保护 输出电流可调节 具有输入欠压保护功能 应用 低压LED射灯代替卤素灯 车载LED灯 LED备用灯 LED信号灯
上传时间： 2014-12-24
上传用户：shengyj12345
基于1 μm 40V BCD 工艺，使用Cadence软件对原边反馈AC/DC控制器进行仿真和分析。线补偿技术可以使原边反馈AC/DC电路获得很好的负载调整率，抵消电感上所消耗的电压和整流二极管上的压降，使输出达到的最佳值。在输入加220 V交流电压时，输出结果最大值为5.09 V，最小值为5 V，最大负载调整率为9.609%。
上传时间： 2013-10-20
上传用户：sglccwk
LM2596开关电压调节器是降压型电源管理单片集成电路，能够输出3A的驱动电流，同时具有很好的线性和负载调节特性。固定输出版本有3.3V、5V、12V， 可调版本可以输出小于37V的各种电压。 该器件内部集成频率补偿和固定频率发生器，开关频率为150KHz，与低频开关调节器相比较，可以使用更小规格的滤波元件。由于该器件只需4个外接元件，可以使用通用的标准电感，这更优化了LM2596的使用，极大地简化了开关电源电路的设计。 其封装形式包括标准的5脚TO-220封装（DIP）和5脚TO-263表贴封装（SMD）。 该器件还有其他一些特点：在特定的输入电压和输出负载的条件下，输出电压的误差可以保证在±4%的范围内，振荡频率误差在±15%的范围内；可以用仅80μA的待机电流， 实现外部断电；具有自我保护电路（一个两级降频限流保护和一个在异常情况下断电的过温完全保护电路） ※ 3.3V、5V、12V的固定电压输出和可调电压输出 ※ 可调输出电压范围1.2V～37V±4% ※ 输出线性好且负载可调节 ※ 输出电流可高达3A ※ 输入电压可高达40V ※ 采用150KHz的内部振荡频率，属于第二代开关电压调节器，功耗小、效率高 ※ 低功耗待机模式，IQ的典型值为80μA ※ TTL断电能力 ※ 具有过热保护和限流保护功能 ※ 封装形式：TO-220（T）和TO-263（S） ※ 外围电路简单，仅需4个外接元件， 且使用容易购买的标准电感
上传时间： 2014-12-24
上传用户：ttpay
Automobile electronic systems place high demands ontoday’s DC/DC converters. They must be able to preciselyregulate an output voltage in the face of wide temperatureand input voltage ranges—including load dump transientsin excess of 60V and cold crank voltage drops to 4V. Theconverter must also be able to minimize battery drain inalways-on systems by maintaining high effi ciency over abroad load current range. Similar demands are made bymany 48V nonisolated telecom applications, 40V FireWireperipherals and battery-powered applications with autoplug adaptors. The LT3437’s best in classperformancemeets all of these requirements in a small thermallyenhanced 3mm × 3mm DFN package.
上传时间： 2013-10-15
上传用户：stampede
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
