试设计一种彩灯控制器控制8盏灯。该彩灯控制器有4种自动切换的花样。第一种花样为彩灯从右到左,然后从左到右逐次点亮,全灭全亮;第二种花样为彩灯两边同时亮一个逐次向中间移动再散开;第三种花样为彩灯两边同时亮两个逐次向中间移动再散开;第四种花样为彩灯两边同时亮三个,然后四亮四灭,四灭四亮,最后一灭一亮。四个花样自动变换,重复以上过程。输入时钟频率为500Hz,灯亮的时间在1—4秒之间,可以自由控制。电路中以“1”代表灯亮,以“0”代表灯灭。
上传时间: 2017-06-21
上传用户:csgcd001
双电源自动切换控制原理图
上传时间: 2013-07-24
上传用户:eeworm
专辑类-开关电源相关专辑-119册-749M 双电源自动切换控制原理图-3页-0.5M.pdf
上传时间: 2013-06-12
上传用户:sunzhp
文章在分析电路噪声、等效噪声输入带宽和自动增益控制原理的基础上, 介绍了一种低频接收机自动增益控制电路的设计。
上传时间: 2014-12-23
上传用户:shfanqiwei
某酒店火灾自动报警系统电路图纸
上传时间: 2013-10-22
上传用户:huyanju
量程自动切换数字电压表
上传时间: 2013-11-05
上传用户:moshushi0009
基于幅移键控技术ASK(Amplitude-Shift Keying),以C8051F340单片机作为监测终端控制器,C8051F330D单片机作为探测节点控制器,采用半双工的通信方式,通过监控终端和探测节点的无线收发电路,实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线,天线直径为(3.4±0.3)cm。试验表明,探测节点与监测终端的通信距离为24 cm,通过桥接方式,节点收发功率为102 mW时,节点间的通信距离可达20 cm。与传统无线收发模块相比,该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller, using half-duplex communication mode, this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter (3.4±0.3) cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm,the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules, the circuit has wide application prospect in small size, low cost and low power consumption and other characteristics.
上传时间: 2013-10-19
上传用户:xz85592677
本文介绍了AD8337的芯片特点和工作原理,并结合实际应用给出了一种利用AD8337设计的自动增益调节电路及实验结果
上传时间: 2013-11-20
上传用户:xjy441694216
有关语音的滤波以及自动增益控制电路的原理图以及PCB图
上传时间: 2015-11-25
上传用户:yt1993410
电视音视频自动控制软件,可实现电视音视频自动切换
上传时间: 2016-01-15
上传用户:xinzhch